How to Splice Electrical Wires (2022)

A great many electrical projects require you to join (splice) circuit wires together. Sometimes this occurs at fixture boxes, but it also can occur wherever you want to branch a circuit into two or more directions. When splicing is done outside a standard fixture box, the project involves making the cable connections inside a junction box that has a blank cover that can be accessed whenever you need to work on the wires.

Learning the splicing technique will make it possible to tackle countless projects that enhance your living space, such as moving an outlet or light fixture, removing a wall, finishing a basement, or taming dangling wires that are improperly connected.

Making wire splices is not a difficult technique. But like any electrical repair that involves handling circuit wires, DIYers should have a good understanding of electrical systems as well as some experience with basic electrical repairs.

The project shown here assumes that the wall surfaces are open to provide access and that the electrical cables have already been run inside the wall cavities. If not, the process of fishing cables will make the project more complicated and time-consuming.

1:52

Watch Now: How to Splice Electrical Wire

Safety Considerations

Any project that involves working with circuit wires requires that you first turnoffthe power to the circuit at the service panel (breaker box).

Electrical splices can never be left on their own in a wall or ceiling cavity. Instead, allsplices must be containedwithin an approved junction box or fixture electrical box. The box itself must remain accessible and cannot be hidden behind drywall or other building materials that would require removal to get to the box.The junction box provides a safe environment for your splices, protecting them against impact and containing sparks and fireif anything should go wrong. While junction boxes may at first seem unwieldy and unnecessary, you will find that they are easy to work with and will make your work safer.

Tip

Junction boxes come in both plastic and metal varieties. Some electricians prefer the durability of metal boxes, but if you use a metal junction box, remember that it will need to be connected to the ground system with a grounding pigtail wire. One end of the pigtail is grouped together with the circuit grounding wires, while the other end is screwed directly to the metal box. No grounding pigtail is required with plastic junction boxes.

The method demonstrated here is the correct way to splice electrical wires using UL-approved wire connectors joined inside an approved electrical box. These connectors can be the familiar twist-on wire nuts or newer style push-fit connectors. This is the method approved by the National Electrical Code (NEC). The old, informal method of splicing wires together with electrical tape should never be used.

How to Splice Electrical Wires (1)

Need more help? Talk to an electrician near you

Our partners can help you compare quotes from top-rated professionals near you

Get a Quote

Advertiser Disclosure

The offers that appear in this table are from partnerships from which The Spruce receives compensation.

(Video) AWESOME IDEA! HOW TO TWIST ELECTRIC WIRE TOGETHER!
(Video) How to splice wires - how to solder, how to crimp, wire connectors

Equipment / Tools

  • Cable ripper
  • Wire stripper
  • Hammer
  • Screwdriver
  • Pliers
  • Cordless drill with driver bit
  • Drill bit extender (if needed)

Materials

  • Metal junction box with cover
  • Cable clamps for box
  • UL-approved wire connectors
  • Wood screws for mounting box
  • Grounding pigtail wire
  1. Remove Outer Sheathing From Cable

    Make sure that you are joining two similar cables.The cables must match in terms of wire gauge and the number of individual conductors in the cable.Modern wiring (up to 50 years old or so) will have the gauge and number of wires printed on the outer sheathing of the cable. For example, a cable labeled "12/2 w ground" contains two 12-gauge insulated conductors plus a bare copper grounding wire.

    First, expose the individual conducting wires within the tough outer plastic jacket by using a cable ripper to slice through the sheathing. Do not use a utility knife, as you risk cutting into the individual wires. Insert the cable into the hole on the cable ripper until it is about 6inches from the end of the cable. Lightly press the sides of the ripper together and draw the tool off the end of the cable to slice through the sheathing.

    Trim away the severed portion of the sheathing and paper filler with the cutting jaws on a wire stripper or with a utility knife.

    How to Splice Electrical Wires (2)

  2. Strip Insulation From Conductors

    Every conducting wire in the cable, except for the ground wire, will be coated with color-coded plastic insulation. Use a wire stripper to remove about 1/2 inch of this insulation from each wire. The stripper tool has slots to match various wire gauges; use the slot that matches the wires in your cable.

    How to Splice Electrical Wires (3)

  3. Inspect the Cables

    Check the wiring on both cables for any sign of damage, such as cut, chewed, or burned insulation or nicked wiring. When the cable sheathing and wire insulation are properly prepared, about 6 inches of wire should protrude beyond the edge of the remaining sheathing, and individual wires should be stripped back and smooth, not nicked.

    How to Splice Electrical Wires (4)

  4. Remove Knockouts From Junction Box

    With a screwdriver and hammer, loosen two opposing knockout disks from the junction box. Use pliers to pry off and completely remove the discs. Often, you have to rock the disk back and forth several times before it will come free. Dispose of the disks.

    How to Splice Electrical Wires (5)

  5. Attach Cable Clamps to the Junction Box

    Plastic cable clamps usually just snap into the knockout openings in the box. For metal cable clamps, first remove the threaded tightening ring, then insert the clamp through the knockout opening. Screw the tightening ring back onto the clamp from inside of the box, and use pliers to tighten the ring securely. Do notturn too hard or you may break the clamp.

    (Video) BIGGEST Mistakes DIYers Make When Connecting Wires Together | How To

    How to Splice Electrical Wires (6)

  6. Insert the Cables

    Insert one cable into each junction box knockout, through the clamp. Make sure that the cable is positioned flat on the clamp—if you accidentally position it sideways, you risk damage to the cable. The cable sheathing should extend past the clamp into the box by 1/4 to 1/2 inch. Plastic cable clamps usually have a tab that you force closed in order to grip the cable. With metal clamps, tighten the screws on the clamp until the cable is securely gripped.

    How to Splice Electrical Wires (7)

  7. Attach the Box and Cover Plate

    The junction box has holes in the back and sides to allow you to screw it to a wood framing member. If necessary, you can attach a bit extender to a drill to help you drive screws without disturbing the wires. Make sure the box is securely attached to the framing member at a depth that will allow the cover plate to fit securely over the box once the finished wall or ceiling surface is in place. For example, if the wall will be finished with 1/2-inch drywall, then the front edge of the box should extend 1/2 inch beyond the front face of the stud. This will ensure that the box will be flush with the finished wall surface.

    How to Splice Electrical Wires (8)

  8. Make the Wire Connections

    Using approved wire connectors, join together the conducting wires with similar insulation colors.

    With standard wire nuts, some electricians prefer to twist the wires together first with pliers, then screw the wire nuts over the ends of the wires. However, some wire nut manufacturers instruct to simply hold the two parallel wires together, then twist the wire nut over the bare ends of the wires in a clockwise direction. However you do it, the wires should be connected securely enough that they don't come free from the wire nut when you tug on them. There should be no bare wire exposed at the bottom of the wire nut. Some electricians like to wrap a loop or two of electrician's tape around the base of the wire nut and wires to help reinforce the wire connection.

    Another type of approved wire connector is the push-fit connector. With these connectors, you simply push the bare end of the wire into a grip-fit socket on the connector.

    The bare copper circuit grounding wires should also be joined together in the box, using an approved connector. For metal electrical boxes, run a third grounding pigtail (bare copper or green insulated) to the two bare copper circuit grounding wires, using a wire connector. The free end of the pigtail is then connected to a threaded screw opening on the metal box, using a green grounding screw. This technique grounds the electrical box and improves the safety of the circuit.

    After completing the connections and finishing the wall or ceiling surface around the box, attach the cover plate securely. Some cover plates have a matte surface that allows them to be painted.

    How to Splice Electrical Wires (9)

How to Run Electrical Wire Through Finished Walls

(Video) Tutorial Time: Proper Wire Splicing
(Video) How to make a junction box -- wire splicing

FAQs

How do you extend a wire that is too short? ›

If there's not enough wire left to do that then straighten out the old loops prepare three 6-inch

How do you splice multiple electrical wires together? ›

So the first thing you're going to want to do when you have your splicing wires is you're just going

How do you splice electrical wires? ›

Using electrician's pliers, twist together the stripped ends of the corresponding wires from each strand of 12/2 Romex, white wire to white and black to black. Twist them until they are tightly joined, and secure each joint with a threaded wire cap/nut. Fold both sets of wires neatly into the junction box.

Can I make a wire longer? ›

Solution: Extend wires | If you run into short wires, there's an easy fix. Simply add 6-in. extensions onto the existing wires. The photo shows a type of wire connector that's easier to install in tight spots.

Can you splice wires without a junction box? ›

Short answer: NO. Long answer: All splices must be in a junction box, and the junction box must be accessible.

Videos

1. WIRE SPLICING step by step!
(Think Reno)
2. Proper Joint of Electric Wire
(EASY TECH)
3. How To Connect or Splice Wires Together - 10 Methods
(Word of Advice TV)
4. How to Splice Electrical Wires Together & Use Heat Shrink Tubing!
(Flashback502)
5. Awesome Idea! How to Twist Electric Wire Together | Properly Joint Electrical Wire | Tips & Tricks
(Mehboob Electric DIY)
6. How to Splice Wires for Electricians
(BecomingAnElectrician)

Top Articles

You might also like

Latest Posts

Article information

Author: Rev. Leonie Wyman

Last Updated: 10/18/2022

Views: 6048

Rating: 4.9 / 5 (59 voted)

Reviews: 82% of readers found this page helpful

Author information

Name: Rev. Leonie Wyman

Birthday: 1993-07-01

Address: Suite 763 6272 Lang Bypass, New Xochitlport, VT 72704-3308

Phone: +22014484519944

Job: Banking Officer

Hobby: Sailing, Gaming, Basketball, Calligraphy, Mycology, Astronomy, Juggling

Introduction: My name is Rev. Leonie Wyman, I am a colorful, tasty, splendid, fair, witty, gorgeous, splendid person who loves writing and wants to share my knowledge and understanding with you.